extended manual
FAQ/extended troubleshoot
Enter Main Menu
hold the fire and '+' buttons until you see the menu on the display.
Change click combinations
Change in ‘menu>interface>clicks’. 5-click always powers on/off.
WarmUp to Cruise/WarmUp to Tempstep
When 'menu>vaping>W2Cru' is set to:
0 - warmup mode terminates normally and the device waits for
further input.
1 - warmup mode will continue to cruise control automatically.
2 - warmup mode will continue to temperature
stepper.
Set Ecolevel for Eco-Cruise Control
Theoretical energy savings by lowering heater
temperature between draws in Cruise Control.
Set your Eco level in
‘menu>vaping>Ecolevel’.
0: eco features disabled, original Cruise Control. keeps the
heater at the set temperature.
1: the heater temperature is lowered when no draw
is detected.
2: the heater temperature is lowered more than in eco level 1
when no draw is detected.
3: the heater temperature is always lowered to 135degC when no
draw is detected.
Set Up Temperature Stepper
Activate temperature stepping by clicking the
fire button the amount that was set in the clicks menu option.
(4 clicks default).
The session time is equally divided into the amount of steps
set in Tsteps and will steadily increase temperature for each
step.
Cycle through the steps with '+' and '-'.n ‘menu>vaping’ set your session time (timer),
amount of temperature steps (Tsteps), the starting temperature
(LoTemp) and the end temperature (HiTemp).
I
Assign “Tstep” to one of the Clicks in
‘menu>interface>clicks’.
Set Up Cruise Control/Session mode
Assign “Cruise” to one of the Clicks in
‘menu>interface>clicks’.
Set your Cruise duration in
‘menu>vaping>timer’.
Activate Cruise by clicking the fire button the
amount that was set in the clicks menu option. (2 clicks
default)
Cruise will be deactivated automatically when the time is up
or when it is aborted with a single click of the fire button.
Set Up WarmUp-mode
Assign “WarmUp” to one of the Clicks in
‘menu>interface>clicks’.
Activate WarmUp by clicking the fire button the
amount that was set in the clicks menu option. (3 clicks
default)
The warming up automatically shuts off when the threshold
watts are reached. It can be interrupted by single clicking
the fire button.
TUBO seems to run cold
Increase the resistance in ‘menu>coils>manage>TCR’ by 0.002. Make sure the lock symbol is after the number before you leave. repeat if necessary.
TUBO seems to run hot
Decrease the resistance in
‘menu>coils>manage>TCR’ by 0.002. Make sure the lock
symbol is after the number before you leave. repeat if necessary.
Change peak power
Assign
"Edit" to one of the clicks in 'menu>interface>clicks'. Go back
to main screen and click the fire button according to the clicks menu.
The top
line starts to flash. Navigate to the ‘PWR’ line by
clicking ‘-‘ and
press ‘+’ to start changing the value and save with
the fire
button. Recommended value is 70watts.
Activate 1°C/5°F increments
Switch the option in 'menu>interface>1CF5'
to ON.
Change 3rd line display
The third line on the main screen can be switched
to display different properties, default is current (AMP).
Enter main screen edit mode by clicking the fire
button according to clicks menu until top
line flashes. Navigate to the third line by clicking ‘-‘ and
press ‘+’ to change the display info. Set by clicking the fire
button. Third line will show when in on demand operation or when the device is idling.
Activate power (wattage) mode
In ‘menu>vaping>modes’ activate power mode by setting ‘power’ to ‘Y’. enter main screen edit mode by clicking fire the amount of times you set it in 'menu>interface>clicks' for "edit" until top line flashes. Press ‘+’ until you see ‘TUBO Power’ and select with the fire button. Recommended values for on-demand mode are 35-45 watts. Cruise mode is limited to 20watts in power mode. Do the same to get back to 'TUBO' mode.
There are no products to list in this category.